Ready Now
Caterpillar 140H
CANCELED・ LOAD # 1685026
A. Length33 ft 2 in
B. Width8 ft 1 in
C. Height10 ft 3 in
D. Attachment14 ft 0 in
Weight36,000 lbs
Item is Operable: Yes
Starts and moves under its own power: Yes
Item/Stock #:Lot 186
Cargo Value:53000
Year:1996
Important Load Information
1996 140H
Location
Pickup Site
Perris CA 92571 USReady to Load: 4/21/2025 10:30 AM
Loading dock availableLoading assistance available
Dropoff Site
Cedar City UT 84721 USDeliver By: 4/25/2025 5:00 PMHours: 7am 5pm
Loading dock availableLoading assistance available
Load Advisor
Item Type: Motor Graders
Shipper Verified
Machine has a Multi Shank Ripper attached.
Loading Dock is available at both pickup and drop-off locations.
Shipper has NOT VERIFIED item's dimensions.
Shipper VERIFIED that item starts and moves under its own power.
Compliance
Permit required for height.
Escort/pilot vehicle required.
Permit required for width.
Recommended Trailers
Stepdeck
Double Drop
Sliding Axle or Landoll
Lowboy or RGN
Lowboy Drop Rail or Exposed Center Beam
Extendable StepDeck
Stepdeck
Extendable StepDeck
Questions & Answers
Question: How wide ?
8’ 1” with the blade angled
Question: - Hello, can the blade be angled?_Emilio C.
Yes
Thank you for your response. I have submitted my bid and would appreciate it if you could accept it so we can coordinate directly. If you have any questions, please feel free to reach out. We are here to assist you. Emilio C.
Question: Hi, congratulations for your new motor grader!!! I see in the pictures it looks in neat condition, and while going through the details I see that it is fully operable and can be driven up the trailer ramps. I did some reasearch and found that oncethe blade is angled it becomes 11'9'' wide. Can you help me to confirm this? Please let me know so I can make it happen. Thank you and best regards. **HANS**
Question: Hi, congratulations for your new motor grader!!! I see in the pictures it looks in neat condition, and while going through the details I see that it is fully operable and can be driven up the trailer ramps. I did some reasearch and found that oncethe blade is angled it becomes 11'9'' wide. Can you help me to confirm this? Please let me know so I can make it happen. Thank you and best regards. **HANS**
Question: Hi, congratulations for your new motor grader!!! I see in the pictures it looks in neat condition, and while going through the details I see that it is fully operable and can be driven up the trailer ramps. I did some reasearch and found that oncethe blade is angled it becomes 11'9'' wide. Can you help me to confirm this? Please let me know so I can make it happen. Thank you and best regards. **HANS**
Question: Hi, congratulations for your new motor grader!!! I see in the pictures it looks in neat condition, and while going through the details I see that it is fully operable and can be driven up the trailer ramps. I did some reasearch and found that oncethe blade is angled it becomes 11'9'' wide. Can you help me to confirm this? Please let me know so I can make it happen. Thank you and best regards. **HANS**
8’1” width with the blade angled I understand. Based on cat’s website
Hi, I kind of like trigonometry, so I see that this blade that is 12'3'' wide. Cat's website says that you can angle it 40 degrees. That will pretty much make the width 9'4'' after angling it. A blade that wide can't be angled to the point where it is 8'6'' or less, you'll have to angle it too much. Unless they can remove the blade, this will definetly require overwidth permits. I have already updated my BID and removed the escorts from my quote and left it valid for an RGN / Lowoboy trailer
with overwidth permits included. Please accept so we can proceed with getting this hauled asap or let me know if you have any questions. Thank you.
Question: Good morning. Can you please confirm blade will angle to 8'6" or less?
